REQUEST A QUOTE  -  STREAMLINED BACKSHOP INSTALLATIONS AND REPAIRS  -  MORE INFO 
ZIMO DCC

ZIMO Capacitor - ELKSOGR Electrolytic Cap Collection

(No reviews yet) Write a Review
MPN:
ELKSOGR
Condition:
New
Availability:
Backorders Accepted
MSRP: $33.64
Price: $26.91
— You save $6.73

Description

ZIMO Capacitor - ELKSOGR Electrolytic Cap Collection

 

For 5 - 10 Zimo Large Scale decoders WITH 16 V - energy storage port (= integrated energy storage circuit) including MX695, MX696,MX697, and MX699 types.

These models only require a capacitor (no other components) connected to the appropriate terminals or solder pads or via the interface connector since the additional devices and circuitry are designed in the decoder.

You can and should use multiple capacitors, wired in parallel, to improve the effectiveness of the device.  The only limit on the number of capacitors to be used is the available space.

The ELKSOGR collection includes 5 pieces each of:

  • Capacitor - 10000F / 16V (Ø18x35 mm)
  • Capacitor - 22000F / 16V (Ø22X44 mm)


Note: for the older types MX69, MX690 must use additional components (inductors, diodes, resistors) to connect the capacitors; See operating instructions.

Energy Storage (Capacitors & Gold Caps) for Zimo Decoders

Capacitors & Gold Caps are used to store energy in model locomotives and rail cars.  The Capacitors & Gold Caps connected to the decoder and are used to...

  • Prevent stalling when passing over dirty track and unpowered frogs.
  • Provide uninterrupted sound playback from sound decoders.
  • Eliminate power loss when moving accross HLU and RailCom gaps.

Many ZIMO decoders feature a special connection design to ensure that the use of Capacitors & Gold Caps do not cause excessive charging currents (i.e. "In-rush current") and that they do not interfere with decoder programming or HLU and Railcom communications.

Recommended Applications:

SPEIKOMP, ELKSODR - ZIMO decoders WITHOUT special energy storage port (MX621, MX622, MX630 ...)
ELKSOMT - ZIMO decoders WITH 25 V - energy storage port and limited load capacity (MX631, MX632, MX644 ...)
ELKSOPL - ZIMO decoders WITH 16 V - energy storage port and limited load capacity (MX633, MX645, ...)
ELKSOGR, GOLD CAPS - ZIMO decoders WITH 16 V - energy storage port and unlimited loading capacity (MX696, MX697, MX699, ...)

ZIMO recommends traditional electrolytic capacitors for use with small scale decoders (N, HO) because the gold cap solutions are large (usually largerer than the decoder itself) and expensive.  Moreover, the gold caps are not really necessary because ZIMO decoders are designed with capacitors already on board. In addition, the "ordinary" cheap capacitors provide excellent long-term performance.

ZIMO offers a broad range of solutions, including capacitors or gold caps, for use with large scale decoders. In most cases, the use of simple capacitors (about 10,000 to 50,000 microfarads) is sufficient.  The cost of this solution is very low and they can provide power for a few tenths of a second up to the full second range.  

The effectiveness of electrolytic capacitors (see assortment ELKSOGR) is highly dependent on total amount of capacitance added to the model and power consumption of all of the devices in the model.

If greater capacitance or storage time is needed, Gold Cap arrays can be manufactured or purchased to provide an exponential increase in power. A product like the GOLDSORG can supply several seconds of electricity to a decoder when power is lost.
 
Multiple electrolytic capacitors, wired in parallel, can be used in each engine to increase the total amount of capacitance and therefore increase the amount of energy stored in the model.
  

View AllClose

Additional Resources

MANUFACTURERS WEBSITE:
SOUND CONFIGURATION & SOUND FILE RESOURCES:
FIRMWARE & SOFTWARE RESOURCES:
PRODUCT MANUALS & TECHNICAL DOCUMENT RESOURCES:
MANUFACTURERS WARRANTY & REPAIRS:
ADDITIONAL INFORMATION - DCC TIPS:
ADDITIONAL INFORMATION (1):
NA
ADDITIONAL INFORMATION (2):
View AllClose

Additional Information

PRODUCT CLASS :
All Scales
DECODER TYPE:
Keep-Alive Capacitor
SIZE-INCH (Dia x H):
D0.88 x 1.79 in
SIZE-METRIC (Dia x H):
D22.3 x 45.5 mm
KEEP-ALIVE INTERFACE:
Hardwire - 2 Radial Wire Leads w/ Free Ends
KA INPUT VOLTAGE (MAX):
16V
KA TOTAL CAPACITANCE:
22000uF + 10000uF*
ADDITIONAL FEATURES:
5pcs each size
NOTES (1):
* SIZE-INCH (Dia x H)=D0.71 x 1.42 in
NOTES (2):
* SIZE-METRIC (Dia x H)=D18.1 x 36.1 mm
View AllClose