Search
Browse by Manufacturer
Browse Categories
Price Ranges


Search Shopping Lists


 



 DCC Tools




DCC Standards









 
 
TBD
-------------------------

TBD
-------------------------

TBD 
-------------------------

TBD

Stop by and say Hi!
 

 
Be sure to see us on
 
 






 












 

Be Sure To Check Out
The Latest Gear From
These Great DCC 
Manufacturers













The DCC Gurus












Olin's Depot OC1 Quad DCC Block Occupancy Detector Unit

<< Previous in DCC - Accessory Decoders, Block Detection, Signaling Next in DCC - Accessory Decoders, Block Detection, Signaling >>
MSRP: $59.95
Sale Price: $29.97
You Save: $29.98
[ 1 ] pcs In Stock
 
Backorders Accepted
 
Item Number: OD-OC1
Manufacturer: Olin's Depot
Manufacturer Part No: OC1
on sale


Olin's Depot OC1 Quad DCC Block Occupancy Detector Unit

The OC1 is a four-segment DCC block occupancy detector.  It is completely powered from DCC, and provides four optically-isolated outputs with a common ground.  The advanced microcontroller design allows for previously unavailable occupancy detection features, including compensating for the unoccupied current level and easy sensitivity setting in small calibrated steps.  A single axle with a 10 kΩ resistor between the wheels can be reliably detected.

Features
  • Zero level compensation. After you connect the OC1 to DCC power and the track segments, you remove everything from the track and press the button (see operations section for details). This measures the current when the track is unoccupied and saves these value for each segment in the digital memory of the processor. During normal operation, the saved zero levels are subtracted from live readings before determining whether a segment is occupied. This greatly reduces false readings due to leakage and capacitive coupling such as from twisted pair wires. 
  • Adjustable sensitivity from 1/4 milliamp (mA) to 3 3/4 mA in 1/4 mA steps. For reference, a single 10 kΩ resistor accross the track draws from about 1 mA to over 2 mA depending on the DCC voltage. 
  • Optional 2 second hold time. The unit can be configured to hold all occupied indications for at least 2 seconds, or to make the outputs immediate. 
  • Supports up to 4 amps current per segment. 
  • Isolated outputs. The outputs are completely isolated from the DCC power via opto-couplers. 
  • Occupied indicator LEDs for each segment. 
  • Low voltage drop. The electronic sensors drop only 400 mV at full current and less at lower current. 
  • The open-collector outputs can sink 25 mA, allowing most common LEDs to be driven directly without additional relays or transistors. 
  • Can drive digital logic inputs with only a single added pullup resistor per segment.


Introducing Baseline Capture by Olin's Depot



Baseline capture is another DCC occupancy sensing innovation from Olin's Depot

Do your occupancy sensors trip when there is nothing on the track?  You fiddle with the sensitivity, and now they don't trip when they should?  Can't adjust them so they work right?  You use different wires or move your wires around, and now they are all messed up again?  The humidity changes and you're back to the beginning? 

NOT ANYMORE

 

The Problem

 

In a DCC system, even empty track will electrically draw some current.  This is because the fast-changing voltage used by DCC allows some current to jump between nearby wires, right through the insulation.  The amount of current that jumps depends on the length of the wires, how close they are to each other, where they are relative to other wires, and even the humidity. 

A single axle with just a resistor can draw less current than this background, or baseline, level.  This makes traditional occupancy detectors that measure current unreliable. 

Traditional occupancy detectors give you a single "sensitivity" adjustment at best.  This can be adjusting a knob or even as crude as changing the number of loops of wire that pass through the sensor.  The problem with all these methods is that it is difficult to set the system to ignore the inevitable baseline current but detect the basline plus just a resistor axle.  

 

The Solution

 

The Olin's Depot OC1 DCC occupancy sensor measures and remembers the baseline level in a digital memory.  When you first set up the system, you take everything off the track being sensed, then press and hold down the button (shown in the picture above) for one second.  This causes the on-board microcontroller to measure the baseline level and save it in the digital memory.  The digital memory will remember that baseline level from then on, without drifing due to changing temperature, humidity, or over time. 

If you change the wires to the track, move them around, or other things near them change, you only need to have the unit take another baseline measurement.  Your sensitivity setting will not need to change because it too is stored in a digital memory.  

 

Reliable Detection

The saved baseline level, the advanced current sensing circuit, and the sophisticated digital controller provide reliable and accurate occupancy detection in the OC1 far ahead of other devices.  The OC1 can be adjusted in calibrated 1/4 milliamp steps above the baseline level.  This makes the OC1 more reliable and easier to set up than traditional occupancy detectors. 



Connections

Input

The OC1 can be connected to up to four track segments at a time as shown in this diagram:


DCC power does not have a polarity, so can be hooked up either way. The DCC line connected to the Pwr terminal must also be connected to the common rail for all track segments covered by the OC1 unit. The other DCC line must be connected to the Ret terminal. The Seg1 thru Seg4 terminals are connected to the other individual rails for each track segment. Note that this side of the rail must be separate for each track segment. Use insulating spacers or gaps as necessary.

When sufficient current is detected accross track segment 1 (Seg1 terminal), the OC1 output will be asserted. Likewise, current in segment 2 will assert the OC2 output, etc.

Output

The five output terminals (Comm, OC1, OC2, OC3, OC4) are completely floating relative to the DCC power.

In electronics jargon, the OC1-OC4 signals are NPN open-collector outputs with Comm being the common emitters. In practical terms, you can think of there being four switches. Each OC1-OC4 terminal is connected to one end of one switch, and the other ends of all four switches are connected to Comm. When occupancy for a segment is detected, the switch is turned on, otherwise it is left off. In essence, each OCx output is shorted to Comm when occupancy is detected, otherwise not.

Unlike normal mechanical switches, these solid-state switches can only handle voltage in one direction. Comm must always be at the same or lower voltage than any of the OCx outputs. Normally Comm is connected to ground. The OCx outputs then either connect their lines to ground or effectively stay disconnected.

The maximum current thru each switch must also not be exceeded. These switches can handle up to 25 mA (milliamps). That is sufficient to light most ordinary LEDs, which are usually rated for 20 mA maximum.

Here is a example connecting LEDs so that they light when a track segment is occupied. This assumes separate 5 volt power is available:


With a 5 volt supply, you should not use resistors smaller than 160 Ω since that results in nearly the maximum of 20 mA the LEDs can handle. Most LEDs are still quite bright with 10 mA current. If that is sufficient, use 270 Ω resistors.

Most LEDs that look like what is shown in this diagram have two leads of different length, with the longer one being the positive connection. However, this is not a universal rule, and you should try flipping the LED around if it does not light. The fancy electronics name for the positive lead (connected to the resistor in the diagram) is the "anode", and the other lead the "cathode". If the LEDs are built into other equipment, like signal lights, then the documentation may only describe them with those terms.

Operation

Button

Various settings can be selected via the single user button labeled Config. Different button actions are distinguished by different sequences of short and long presses of the momentary button. A short button action is called a "click", which is the button held down for less than 1/3 second. A long action is called a "press", which is the button held down for more than 1/3 second. For successive button actions to be part of a sequence, the gap between actions must not exceed 1/2 second.

All settings persist until deliberately changed, whether power is shut off or not.

The valid button sequences are:

Press

Saves the immediate measured current values as the zero current level. For occupancy to be detected, the measured current must exceed this level by the trigger threshold. The zero current level is measured and saved for each track segment separately.

This action is confirmed by all four lights flashing together for a short time.

Click

Turns off the occupancy hold time. The occupancy outputs will indicate the immediately measured conditions. This mode can be useful for setting up and debugging because the result of actions can be seen quickly.

This action is confirmed by the four lights showing in sequence right to left.

Click - click

Turns occupancy hold on. Each occupancy output will continue to be asserted for two seconds after any time occupancy is detected.

This is probably the mode you want to use for normal operation. The wheels of rolling stock don't always make good electrical contact with the track due to dirt and bouncing. This setting prevents small interruptions in current from causing the output to signal no occupancy. Also in many layouts, the signals driven by occupancy are supposed to persist for a few seconds after the a segment becomes unoccupied.

Usually the only reason not to enable the two second occupancy hold during normal operation is if the occupancy signals are driving other equipment that also implements a hold, or driving computer inputs where the software performs its own hold logic.

This action is confirmed by the four lights showing in sequence left to right.

Click - press

Lowers the threshold for detecting occupancy. Occupancy is determined by the measured current minus the calibrated zero level (see Press above) exceeding the threshold. This threshold can be adjusted from 1 to 15, which is in units of 1/4 milliamp. The factory default is 7 (about 1 3/4 milliamps).

Decrease this setting if you find occupancy is not being detected when it should be. Keep in mind that occupancy is detected by rolling stock drawing current. Unpowered cars usually don't draw any current, so can't be detected without deliberate resistors connected between opposite wheels. The OC1 is sensitive enough so that only 10 kΩ should be needed. A 10 kΩ resistor draws such a tiny amount of the power that many axles can be equipped with these resistors without significant effect on the total power budget. For example with 22 volt DCC, which is the maximum allowed by the DCC standard, a 10 kΩ resistor draws only 2.2 mA. 20 axles with 10 kΩ resistors would then draw only 44 mA.

Increase this setting if you are seeing too many false occupancy indications. However, check that the zero current level (see Press above) is set properly first.

This action is confirmed by displaying the new 1-15 threshold setting in binary on the lights for one second.

Click - click - press

Like click-press (above), except that the occupancy detection threshold is raised instead of lowered.

Lights

The board has four LEDs labeled OC1-OC4. During normal operation, these provide a visual indication of when occupancy is being signalled for their associated segments. Special displays are shown on power up and after button actions. Note that the outputs are asserted whenever the LEDs are lit. This means occupied signals are sent after power up and after button actions, even though the associated track segments may not be occupied at that time. The Button section (above) describes what is displayed to confirm each button action.

On powerup, the lights display patterns to allow visually verifying their operation, and to show some of the current settings. All four lights are flashed together briefly after powerup.

After the initial flash, the occupancy current threshold is shown for one second. This is the same display as follows a increment or decrement of the threshold. See the click-press button action for details.

After the occupancy detect threshold, the lights indicate whether occupancy hold is on or off. The four lights are blinked in sequence, with left to right indicating occupancy hold on, and right to left indicating off. This is deliberatey the same display as after the button actions that set the occupancy hold on or off.


Manufacturers Website: Olin's Depot

 

 

 

Check Out These Related Products...

ESU 53900 LokTester V2.0 DCC Decoder Test Station
MSRP: $52.90
Price: $42.32
You Save: $10.58
[ 8 ] pcs In Stock
 
ESU 53900 LokTester V2.0 DCC Decoder Test Station
Good Deals DCC - TT-10 - The Programmer Test Track - HO-N Scale Combo Test Track
MSRP: $78.70
Price: $62.96
You Save: $15.74
[ 4 ] pcs In Stock
 
Good Deals DCC - TT-10 - The Programmer Test Track - HO-N Scale Combo Test Track
Model Railroad Technologies Accutrack II Train Speedometer
MSRP: $81.95
Sale Price: $65.90
You Save: $16.05
[ 14 ] pcs In Stock
 
Model Railroad Technologies Accutrack II Train Speedometer
on sale
SBS4DCC "Sugar Cube" Speaker 11x15mm 8 ohm 1 watt w/ Double Deep Sound Chamber
MSRP: $11.50
Price: $10.35
You Save: $1.15
In Stock
 
SBS4DCC "Sugar Cube" Speaker 11x15mm 8 ohm 1 watt w/ Double Deep Sound Chamber
SBS4DCC "Sugar Cube" Speaker 13x18mm 8 ohm 1 watt w/ Double Deep Sound Chamber
MSRP: $16.50
Price: $14.85
You Save: $1.65
In Stock
 
SBS4DCC "Sugar Cube" Speaker 13x18mm 8 ohm 1 watt w/ Double Deep Sound Chamber
SBS4DCC "Sugar Cube" Speaker 8x12mm 8 ohm .7 watt w/ Double Deep Sound Chamber
MSRP: $11.50
Price: $10.35
You Save: $1.15
In Stock
 
SBS4DCC "Sugar Cube" Speaker 8x12mm 8 ohm .7 watt w/ Double Deep Sound Chamber
SBS4DCC "Sugar Cube" Speaker 9x16mm 8 ohm .7 watt w/ Double Deep Sound Chamber
MSRP: $12.50
Price: $11.25
You Save: $1.25
In Stock
 
SBS4DCC "Sugar Cube" Speaker 9x16mm 8 ohm .7 watt w/ Double Deep Sound Chamber
ZIMO MXTAPV DCC Decoder Test and Connector Board - Large and Small Scale
MSRP: $98.42
Price: $78.74
You Save: $19.68
[ 2 ] pcs In Stock
 
ZIMO MXTAPV DCC Decoder Test and Connector Board - Large and Small Scale

Product Reviews

(0 Ratings, 0 Reviews)
 
INVENTORY
REDUCTION
SALE

Streamlined Backshop
has moved!

Too many engines.
Too many cars.
Too much track.

Great products at 
really, really great prices....


 

 


...featuring 
Real-Time 
Stock Status...
 

Shopping Cart
Your cart is empty.
 
 
   


 
24 - 7 - 365
Any time... All the time.

FREE SHIPPING

On Domestic Orders
Over $150

No Coupon Required 

Select

Free Shipping

Option At Checkout

Please Read Our
Limitations and Exclusions




WE SHIP
INTERNATIONAL
 
 
PLEASE REVIEW OUR
FOR TERMS AND 
CONDITIONS

 



Mailing Lists

MONTHLY NEWSLETTER

Mark up to receive great DCC Tips and information about New Products, Pre-Orders, Sales, and Special Promotions.



CLICK THE BUTTONS
for past newsletters and
great DCC Tip and Tricks

         

         
 


Welcome to SBS4DCC ...

Featuring 

Real-Time Stock Status 

Reporting



Featuring the

Roco smartRail

Rolling Track Display Stand 
with z21 Controlle
r...



... on the spot

Operating Fun!





Featuring the

Streamlined Backshop

"Sugar Cube" Speakers...





… the SWEETEST speaker 
available today!


4 Sizes  ...  14 Baffles

56 Sweet Speaker Options





Featuring the

Good Deals DCC

"The Programmer"
Test Tracks...


... Portable Programming

Made Easy




Featuring the

ESU LokTester

Decoder Test Station...



… take control of DCC Decoder

Testing and Programming!





Featuring The New

ZIMO MXTAP

Decoder Test Stations...




... The Ultimate Decoder

Test Platform!



Featuring the

Model Railroad Technologies

ACCUTRACK II

Scale Speedometer...





SPEED has met it’s MATCH !





Featuring the

TCS TrainSpeed

Digital Model Railroad 
Speedometers




… Permanent 
Model Train Speed 
Measurement and Display ...






 


Be sure to see our ads in 
these great publications.









 
National Model
Railroad Association

 

 
Support the NMRA
 
Join Today!



Layout Design 
Special Interest Group
 
 
Make your model 
railroad more than just 
another track plan!
 

 
 
 
 
Join The NMRA
LDSIG Today!
 

 

OPerations Special 
Interest Group


Stop Running Trains.
Start Model Railroading!


 
 
 
Join The NMRA
OpSIG Today!