REQUEST A QUOTE  -  STREAMLINED BACKSHOP INSTALLATIONS AND REPAIRS  -  MORE INFO 
ESU - Electronic Solutions Ulm

ESU 50095 ECoS Detector Feedback Extension Module

(No reviews yet) Write a Review
UPC:
404464550095
MPN:
50095
Condition:
New
Availability:
Backorders Accepted
MSRP: $64.90
Price: $51.92
— You save $12.98

Description

ESU 50095 ECoS Detector Feedback Extension Module

If required, each ECoSDetector can be supplemented by a ECoSDetector Extension module, which can be easily connected to the ECoSDetector. Every ECoSDetector Extension module offers 32 transistor outputs.

 

Outputs

Each one of the 32 outputs provides current up to 100mA max. Since these outputs are conducted as open collectors", you are able to connect either small light bulbs or LEDs with current limiting resistor directly to it.

The total current of all outputs must not exceed 1.5A! Any DC or AC transformer (15V - 19V) can be used for supply.

 

Track occupancy and block signals

Outputs can be used to display the state of each single-track section externally (e.g. on the track control panel).

Alternatively, you have the possibility to show each track section´s state on the display via a block signal (red/green).

The transistor outputs of the ECoSDetector Extension module can be easily programmed within the required operational mode via your ECoS command station.

 

Track control panel

However, the combination of the ECoSDetector and the Extension module is capable to do even more: Just go ahead and built your own track control panel! To make this possible, you need to connect push buttons or toggle switches to the ECoSDetector´s outputs, which is then able to operate turnouts and routes over the command station.

The transistor outputs of the Extension module are meant for illuminating track sections. The whole configuration procedure can be easily completed on the display of your ECoS command station.

If you wish to built a larger track control panel, you can also combine several ECoSDetector modules. In doing so, you are able to built and control up to 100 track control panels per layout.

 

Technical Data

  ECoSDetector
Operational modes: Direct bus connection to ECoSlink. Operation with ECoS or Central Station Reloaded V3.0.0. is possible.
Feedback section: 16 feedback modules.
  Configurable by using jumpers as digital inputs (e.g. for contact tracks or reed switches) or as track occupancy detectors (current sensor).
  Galvanical isolation of feedback modules and command station
  Max. 3A current load per feedback input
RailCom®: 4 of 16 feedback sections can be used as RailCom feedback sections ("local detector"), if desired. Recognition of loco address
Dimensions: 86mm x 86mm x 25mm (3.39 x 3.39 x 0.98 inch)
Included in delivery: ECoSDetector feedback module, terminals, ECoSlink bus connection cable, extensive instruction manual
   
  ECoSDetector Standard
Operational modes: Directly connected to ECoSlink bus. Operation with ECoS command station and Central Station Reloaded V3.0.0 possible.
Feedback section: 16 feedback modules as digital inputs (e.g. for contact tracks or reed switches). Galvanical isolation of feedback modules and command station.
Dimensions: 86mm x 86mm x 25mm (3.39 x 3.39 x 0.98 inch)
Included in delivery: ECoSDetector Standard feedback module, terminals, ECoSlink bus connection cable, extensive instruction manual
   
  ECoSDetector RC
Operational modes: Directly connected to ECoSlink bus. Operation with ECoS command station and Central Station Reloaded V3.0.0 possible.
Feedback section: 4 feedback inputs configured as track occupancy detectors (current sensor). Galvanical isolation of feedback modules and command station.
RailCom®: 4 feedback sections can be used as RailCom feedback sections ("local detector"). Recognition of loco address
Dimensions: 86mm x 86mm x 25mm (3.39 x 3.39 x 0.98 inch)
Included in delivery: ECoSDetector RC feedback module, terminals, ECoSlink bus connection cable, extensive instruction manual
   
  ECoSDetector Extension
Operational modes: Extension module for ECoSDector, is powered and controlled by it. Transistor outputs are powered externally.
Outputs: 32 transistor outputs, 100mA output load each. Construction as open collector is connected to ground
  Total current of all outputs is max. 1.5A
Dimensions: 86mm x 86mm x 25mm (3.39 x 3.39 x 0.98 inch)
Included in delivery: ECoSDetector Extension module, terminals, extensive instruction manual

 

 

View AllClose

Additional Information

PRODUCT CLASS :
All Scales
SIZE-INCH (L x W x H):
0 x 0 x 0 in
SIZE-METRIC (L x W x H):
0 x 0 x 0 mm
ADDITIONAL FEATURES:
NA
NOTES (1):
NA
NOTES (2):
NA
View AllClose